![]() ![]() Click Apply and then Send (if required) in order to send the commands to the ASA.Click OK in order to return to the Group Policy configuration.Be sure that the ACL you just created is selected for the Split Tunnel Network List.Click OK in order to exit the ACL Manager.Define the ACE that corresponds to the local LAN of the client.in order to add an Access Control Entry (ACE). Once the ACL is created, choose Add > Add ACE.Provide a name for the ACL and click OK.Within the ACL Manager, choose Add > Add ACL.Uncheck the Inherit box for Network List and then click Manage in order to launch the Access Control List (ACL) Manager.Uncheck the Inherit box for Policy and choose Exclude Network List Below.Choose Configuration > Remote Access VPN > Network (Client) Access > Group Policy and select the Group Policy in which you wish to enable local LAN access.Configure the Cisco An圜onnect Secure Mobility ClientĬomplete these steps in the ASDM in order to allow VPN clients to have local LAN access while connected to the ASA:.Configure the ASA via the ASDM or Configure the ASA via the CLI.Configure Local LAN Access for the An圜onnect Secure Mobility ClientĬomplete these tasks in order to allow Cisco An圜onnect Secure Mobility Clients access to their local LAN while connected to the ASA: See the Troubleshoot section of this document for more information as well as workarounds for this situation. However, you can browse or print by IP address. ![]() Note: When the client is connected and configured for local LAN access, you cannot print or browse by name on the local LAN. Refer to Set the Split-Tunneling Policy in CLI Book 3: Cisco ASA Series VPN CLI Configuration Guide, 9.17 for information on how to configure split tunneling on the ASA. Note: This is not a configuration for split tunneling where the client has unencrypted access to the Internet while connected to the ASA. Instead, the ASA supplies a default network of 0.0.0.0/255.255.255.255, which is understood to mean the local LAN of the client. Also, unlike the split tunneling scenario, the actual networks in the list do not need to be known. Instead, it defines which networks must not be encrypted. However, unlike the split tunneling scenario, this access list does not define which networks must be encrypted. For example, a client that is allowed local LAN access while connected to the ASA from home can print to its own printer but cannot access the Internet unless it first sends the traffic over the tunnel.Īn access list is used in order to allow local LAN access in much the same way that split tunneling is configured on the ASA. Unlike a classic split tunneling scenario in which all Internet traffic is sent unencrypted, when you enable local LAN access for VPN clients, it permits those clients to communicate unencrypted with only devices on the network on which they are located. If it is permitted, traffic destined for the Internet is still tunneled to the ASA. This configuration allows the Cisco An圜onnect Secure Mobility Client secure access to corporate resources via IPsec, Secure Sockets Layer (SSL), or Internet Key Exchange Version 2 (IKEv2) and still gives the client the ability to carry out activities such as printing where the client is located. The client is located on a typical Small Office / Home Office (SOHO) network and connects across the Internet to the main office. If your network is live, ensure that you understand the potential impact of any command. All of the devices used in this document started with a cleared (default) configuration. The information in this document was created from the devices in a specific lab environment. Cisco An圜onnect Secure Mobility Client Version 2.Cisco Adaptive Security Device Manager (ASDM) Version 7.1(6).The information in this document is based on these software and hardware versions: ![]() Refer to CLI Book 3: Cisco ASA Series VPN CLI Configuration Guide, 9.17 for configuration assistance if needed. This document assumes that a functional remote access VPN configuration already exists on the Cisco Adaptive Security Appliance (ASA). This document describes how to allow the Cisco An圜onnect Secure Mobility Client to access the local LAN while connected to a Cisco ASA. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |